Tank – Page 2 – Vietnam Miniatures Game

Posted on December 3, 2017April 16, 2018 by

M551 Sheridan (VUS002) Assembly Guide

Step 1. Begin assembly by attaching the tracks to the hull of the M551 Sheridan. Note: Each track has been keyed to correspond with a particular side of the hull; this aids in ensuring the correct orientation of the tracks when assembling the miniature.
Below: The correct alignment for the left-hand side track.	Below: The correct alignment for the right-hand side track.	Below: The left-hand side track attached to the hull.

Tip: When referring to left or right-hand side in regards to a Flames Of War miniature, the orientation is determined as if looking at the vehicle from the rear.

Below: The right-hand side track attached to the hull.	Step 2. Attach the driver’s vision hatch to the front of the M551 Sheridan.	Below: The driver’s hatch vision correctly attached to the front of the M551 Sheridan.

Step 3. Next, attach the M81 152mm gun to the front of the turret.	Below: The M81 152mm gun correctly attached to the front of the M551 Sheridan turret.	Step 4. The smoke dischargers attached to the underside of the M551 Sheridan turret. Each side has been keyed to corresponding part. The right-hand side can be seen below.

Below: The left-hand side smoke discharger recess.	Below: The corresponding left and right-hand side smoke dischargers keyed to match the turret.

Below: The smoke dischargers correctly attached to the M551 Sheridan turret.	Step 5. Next, attach the loader’s hatch to the top of the turret.	Below: The loader’s hatch attached to the top of the turret.

Step 6. Time to begin assemble of the commander’s hatch. Begin by attaching the .50 cal MG to the mount located at the front of the hatch. See the examples below.		Step 7. Next, attach the gun shield to the front of the .50 cal MG.

Below: The gun shield attached to the .50 cal MG.	Step 8. Finally, attach the bird-cage armour to the rear of the commander’s hatch.	Below: The fully-assembled commander’s hatch complete with bird-cage armour.

Step 9. Next, attach the fully-assembled commander’s hatch to the top of the M551 Sheridan turret.		Below: With the commander’s turret in place, the M551 Sheridan is ready for the painting table.

Adding A Vehicle Commander

Step 1. To add a vehicle commander, use the open commander’s hatch rather than the closed commander’s hatch.	Step 2. Assemble the commander’s hatch as seen in the steps above.	Step 3. Attach a vehicle commander figure to the inside of the open hatch.

Step 4. Next, attach the fully-assembled commander’s hatch complete with vehicle commander to the top of the M551 Sheridan turret.		Below: With the commander’s turret in place complete with vehicle commander; the M551 Sheridan is ready for the painting table.

US Vehicle Painting Guide

Posted on December 3, 2017April 17, 2018 by

M551 Sheridan Spotlight (VUS002)

Includes one M551 Sheridan

The M551 Sheridan was developed as an amphibious cavalry tank or air-landing tank capable of tackling Soviet tanks. As a result its main armament was an anti-tank missile launcher that could also fire conventional shells. Getting this complex weapon system to work delayed the introduction of the Sheridan, but it finally reached Vietnam in 1968. Once there, its crews liked its firepower, speed, and ability to cross flooded rice paddies, but missed the thick armour of the much heavier M48 and its ability to smash its way through thick jungle.Check out the M551 Sheridan in the online store here…

The M551 Sheridan was made of light aluminium alloys, like the M113, giving it considerable mobility. It combined this with the punch of a 152mm gun capable of firing ‘beehive’ canister rounds.

The M551 Sheridan

The M551 Sheridan in Flames Of War

Contents of the M551 Sheridan Box Set

Contact the customer service team at [email protected] if you have any issues with any of the components.

Posted on December 3, 2017April 16, 2018 by

M48 Patton (VUS041) Assembly Guide

Step 1. Begin assembly with the tracks.

Tip: Each track is stamped with the letter ‘R’ or ‘L’ and an arrow to indicate correct orientation.

Below: The correct alignment for the left-hand and right-hand side tracks.

Tip: When referring to left or right-hand side in regards to a Flames Of War miniature, the orientation is determined as if looking at the vehicle from the rear.

Below: The left-hand side track attached to the hull.	Below: The right-hand side track attached to the hull.	Step 2. Attach the main gun to the front of the turret.

Below: The main gun attached to the turret.

Step 3. Next, attach the infrared searchlight to the top of the main gun.

Tip: There is a contoured section on the base of the searchlight that attached to the top of the gun.

Step 4. Attach the loader’s hatch to the top of the turret.		Step 5. Next, add the cupola MG to the top of the turret.

Below: The cupola MG in place.	Step 6. Attach the hatch to the rear of the cupola MG.		Note: Later versions of the M48A3 added a ring of version blocks below the cupola MG.

Below: The ring of vision blocks attached below the cupola MG.		Tip: A loader’s hatch MG can be added to the M48A3 at a small points cost.

Below: The .30 cal MG attached to the top of the turret for +5 per tank.	Below: The .50 cal AA MG attached to the top turret for +10 points per tank.	Below: With the .50 cal AA MG in place, the M48A3 is ready for painting.

Adding Tank Commanders
Step 1. Attach the hatch at the rear of the cupola MG in an open position.	Step 2. Add the tank commander figure of choice inside the open hatch.	Step 3. Repeat the process if you wish to add a commander figure in the loader’s hatch.

Below: The commander figure attached to the inside of the open hatch.	Below: With the tank commander’s in place, the M48A3 is ready to hit the painting table.

Posted on December 3, 2017July 19, 2023 by christo

M48 Patton Spotlight (VUS041)

Includes one M48 Patton Tank with optional MG & .50 cal Cuploa MG upgrades and crew figures

The M48 Patton tank was completely modernised version of the WWII M26 Pershing heavy tank, designed to fight Soviet tanks on a nuclear battlefield. Oddly, many of the lessons of WWII had been forgotten and the M48 lacked a stabiliser and was likely to catch fire when penetrated. Its impressive anti-tank capability was of little use in Vietnam.Much more useful was the M336 canister round, popularly known as ‘beehive’, filled with 1281 steel pellets that turned the tank’s main gun into a giant shotgun. The crews often moved the commander’s machine-gun from inside the cupola to on top of it, added another for the loader.

Check out the M48 Patton in the online store here…

The M48 tanks went just about anywhere in just about any season, and their firepower proved decisive in battles like the relief of Fire Support Base Gold. There the tanks led a relief column through dense jungle and arrived, guns blazing, ‘just like the late show on TV, the US Cavalry came riding to the rescue’.

The M48 Patton in ‘Nam

The Contents of the M48 Patton Box Set

Contact the customer service team at [email protected] if you have any issues with any of the components.

Description of Components

a. Tank commander figures Type A.
b. Tank commander figures Type B.
c. Tank commander figures Type C.
d. Tank commander figures Type D.
e. .30 cal MGs.
f. .50 cal AA MGs
g. Cupola MGs.

h. Hatch sprues.
i. Searchlight / vision ring sprues.
k. M41 90mm main guns.
l. Right-hand side tracks.
m. Left-hand side tracks.
n. Resin M48A3 turrets & hulls.

Posted on December 3, 2017July 19, 2023 by christo

M42A1 Duster Spotlight VUS161

Includes one M41A1 Duster & one American head sprue.

The experience of the Korean War led US Army officials to begin the phasing out of the M24 Chaffee in favour of designs based around the more modern M41 Walker Bulldog. Included in the M24 family of vehicles was the M19 GMC. Developed towards the end of the Second World War, the M19 was armed with two of the highly effective 40mm Bofors anti-aircraft guns mounted in an open-topped turret capable of traversing 360º.

Check out the M42A1 Duster in the online store here…

Since the 40mm Bofors was still considered an effective anti-aircraft weapon, the turret of the M19 was simply mated with chassis of the M41 to create the M42 or Duster as it became known as by troops serving in Vietnam.

The first M42s begun arriving in Vietnam during 1966 and as it become clear that the threat of North Vietnamese air power would never materialise, the M42 was quickly put to work in a ground support role. With each gun capable of firing 120 rounds per minute, the 40mm rounds of the M2A1 Bofors proved devastating against both unarmoured ground targets and massed infantry attacks.